On-site blasting and protective coatings for heavy equipment, structural steel, tanks and fleets — we bring the rig to your job site, plant or yard to keep downtime to a minimum.
We blast and re-coat heavy equipment right where it sits, so it never has to leave the job site or rack up trucking and downtime. Excavators, loaders, dozers, drill rigs, trailers, attachments and support gear all build up rust, caked-on grime and chalked, peeling paint that eventually eats into the steel. Media blasting cuts through every layer in a controlled pass and leaves a clean, profiled surface that fresh primer and industrial coatings actually grip.
Because we run dustless and conventional setups, we can strip greasy, rusted iron and then prime and topcoat it in the same visit — blast it, prep it, coat it — so the machine goes back to work protected. Need just the rust gone? See our rust removal service.
Structural steel and tanks fail from the surface in. We blast columns, beams, frames, railings, storage tanks, vessels and process equipment back to bare, sound metal so corrosion-control coatings bond properly and last. Removing the rust, mill scale and old paint to the right surface profile is what makes the difference between a coating that sheds in a season and one that protects for years in Florida's salt and humidity.
Whether it's a warehouse frame, an exterior column, a fuel or water tank or a piece of plant equipment, we contain the work area, blast to the spec the coating calls for, and hand it back ready to prime. For more on our abrasive process, see sandblasting.
We keep commercial fleets and facilities looking sharp and ready for re-branding. Box trucks, service vans, dump trailers and work trucks get stripped of faded paint, decals, old logos and rust so new wraps, lettering or industrial paint go on clean. We also remove painted parking-lot line striping, pavement markings and graffiti from concrete, block, brick and steel without leaving ghost outlines or chewing up the surface.
It's the same approach we take on cars and trucks — controlled, surface-safe stripping that respects thin panels. See our automotive blasting for fleet vehicle work.
The biggest cost of refinishing commercial equipment usually isn't the blasting — it's the downtime, trucking and shop fees of hauling a machine somewhere to get it done. Because we're fully mobile, we eliminate that. We mobilize to your job site, plant or yard, blast and coat in place, and have your asset back in service faster.
We dial in the media — crushed glass, garnet, soda or dustless/wet blasting — and pressure to the substrate and the surrounding area, so we can work near operating equipment and contain the mess. Tell us what needs done and where it sits, and call or text (239) 227-1768 for a free on-site estimate.
We come to you. Our rig travels to commercial job sites, plants, contractor yards, warehouses and facilities from Naples and Marco Island up through Bonita Springs, Estero, Fort Myers, Cape Coral and Golden Gate. If your equipment or structure is in Southwest Florida, we can get to it. See the full service area.
We come to you. SWFL Media Blasters is fully mobile across Southwest Florida — we mobilize our blasting and coating rig to your job site, plant, contractor yard or facility so heavy equipment never has to be trucked off-site. That keeps downtime and transport costs down.
Heavy equipment like excavators, loaders and drill rigs, trailers and fleet vehicles, structural steel and columns, storage tanks and vessels, railings, plant equipment, and concrete or steel surfaces with line striping, pavement markings or graffiti. If it has rust, old paint or a failing coating, we can strip it.
Both. We blast it, prep it and coat it. After stripping back to clean, profiled substrate we can apply primer and industrial or protective topcoats in the same visit, so your asset leaves protected and ready for service — not sitting bare in Florida's salt air.
No. We match the media and pressure to the job, run dustless and conventional setups, and contain the work area. That lets us strip rust off heavy steel and still work safely near operating equipment, thin fleet panels and finished surfaces without warping or gouging them.
Yes. We remove painted line striping, pavement markings and graffiti from concrete, block, brick and steel without leaving ghost outlines or tearing up the surface — ideal for property managers and facilities prepping for re-striping, re-branding or repainting.
We schedule around your operation, contain dust and media, and work in place so equipment isn't out of rotation longer than it needs to be. We'll walk the site, give you a clear timeline with the free estimate, and coordinate so your crews keep moving.
Call or text (239) 227-1768 with what needs blasting, roughly how much, and where it's located in Southwest Florida. We'll give you a free on-site estimate and a clear scope before any work starts.
Free on-site estimates for commercial and industrial work across Naples & Southwest Florida. Call or text (239) 227-1768 and we'll schedule around your operation.
Tell us a little about the job and we'll get right back to you.
Thanks — we'll be in touch shortly to set up your free estimate.